Black & Decker KC460LN Manual de instrucciones descargar pdf (Pagina 7)

Assembly

Fitting and removing a drill bit or a screwdriver bit

(g. B)

This tool uses screwdriver bits and drill bits with a 6.35 mm

(1/4") hexagonal shank.

u To t a bit, insert the bit shaft into the bit holder (3).

u To remove a bit, pull the bit shaft out of the bit holder (3).

Use

Warning! Let the tool work at its own pace. Do not overload.

u Before rst use, the battery must be charged for at least

9 hours.

Charging the battery (g. C)

u Insert the charger plug (6) into the charger connector (7).

u Plug in the charger (5).

u Leave the tool connected to the charger for 12 hours.

The charger may hum and become warm while charging; this

is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C.

Selecting the direction of rotation (g. D)

For drilling and for tightening screws, use forward rotation.

For loosening screws or removing a jammed drill bit,

use reverse rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the forward position.

u To select reverse rotation, push the forward/reverse slider

(2) to the rearward position.

u To lock the tool, set the forward/reverse slider into the

centre position.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/

reverse slider (2).

u To switch the tool on, press the on/off switch (1).

u To switch the tool off, release the on/off switch (1).

LED light

The LED light (4) is activated automatically when the trigger is

depressed. The LED will also illuminate when the trigger is

depressed and the forward/reverse slider (2) is in the locked

off position (central position).

Hints for optimum use

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Use the spindle lock to loosen very tight screws or to

rmly tighten screws.

u Always hold the tool and screwdriver bit in a straight line

with the screw.

u When screwing in wood, it is recommended to drill a pilot

hole with a depth equal to the length of the screw. A pilot

hole guides the screw and prevents splintering or

distortion of the wood. For the optimum size of the pilot

hole, refer to the table below.

u When screwing in hardwood, also drill a clearance hole with

a depth equal to half the length of the screw. For the

optimum size of the clearance hole, refer to the table below.

Screw size Pilot hole ø Pilot hole ø Clearance hole

(softwood) (hardwood)

No. 6 (3.5 mm) 2.0 mm 2.5 mm 3.6 mm

No. 8 (4 mm) 2.5 mm 3.0 mm 4.5 mm

No. 10 (5 mm) 3.0 mm 3.5 mm 5.0 mm

Drilling

u Always apply a light pressure in a straight line with the drill bit.

u Just before the drill tip breaks through the other side of the

workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

u Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you will

get the very best from your tool.

This tool uses screwdriver bits with a 1/4" (6.35 mm)

hexagonal shank. Piranha Super-lok accessories are

designed for use with this tool.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning. Your charger does

not require any maintenance apart from regular cleaning.

Warning! Before performing any maintenance on the tool,

switch off and unplug the tool or remove the battery from the

tool if the tool has separate battery. If the battery is integral,

run the battery completely down. Unplug the charger before

cleaning it.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Black & Decker KC460LN Manual de instrucciones Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Atornilladores Black & Decker KC460LN